本產品主要用于各種金屬、玻璃、真空電鍍、水電鍍、電泳、陽極氧化鋁、電解板、鋁塑板、噴塑、噴粉、靜電噴漆面、烤漆面以及各種天花吊頂氧化板、鏡面板、覆膜板、輥涂板等制品的絲印及移印。 2、產品特性：亮光、附著力佳、快干、耐沖壓。 3、稀釋劑：用我司B-03**稀釋劑或783開油，用718洗網水清洗網版。 4、固化劑：單組份使用，也可選擇添加我司JS-10**固化劑用于增加油墨附著力及物理化學抗性。 5、油墨調配方法：開罐先攪拌均勻，取所需量油墨稀釋到合適印刷粘度。如需添加固化劑，先加固化劑攪拌后靜置10分鐘，待油墨與固化劑完全交聯后再進行稀釋。 6、干燥時間：常溫干燥，表干時間5-10分鐘，實干時間在24小時以內，80℃烘烤20分鐘可快速干燥。 7、添加固化劑后的使用時限：4-6小時，過期請棄用，剩余油墨不可回收。 【性能檢測】 1、3M膠帶劃百格測試：無脫落 2、耐沖壓測試：1mm厚鋁板180°折彎無變化。 3、耐酒精測試：用脫脂棉沾濃度99%工業酒精以500G力水平來回200次無脫色。 【注意事項】 1、先小量試印確認符合要求后再批量生產。 2、做好承印物的表面清除油脂及雜質工作，以促進附著效果。 3、附著力、硬度、耐酸性、耐酒精性、耐化學品性、抗劃傷性、耐磨性等性能的檢測， 需要完全固化后方可檢測。 4、未經允許情況下，不得將本系列油墨與其它類型油墨混用及配色。 5、油墨，稀釋劑使用及儲存時嚴禁煙火。 6、使用時注意施工場所的通風狀況良好，盡量避免皮膚直接接觸。 7、本品不慎濺入口、鼻、眼、耳內，應用大量水清洗或直接求助醫生。 This product is mainly used for metal, glass, water, vacuum plating, electroplating, electrophoresis, anodized aluminum, electrolytic plate, aluminum plate, electrostatic spray, spray, spray paint, paint oxidation of surfaces as well as a variety of ceiling panels, mirror plate, coated sheet, roll-coated sheet products, such as screen printing and pad printing. 2, product features: light resistance, good adhesion, quick-drying, stamping. 3, thinner: with our B-03 special thinner or 783 oil, clean screen with 718 wash water network. 4, curing agent: single-component, or you can choose to add our JS-10 special curing agent used to increase ink adhesion and chemical resistance. 5, ink method: opening mix, obtaining the necessary amount of diluted ink to a suitable viscosity of printing. If you need to add curing agent, reinforcing agent first stir and let stand for 10 minutes until the ink completely cross-linked and then diluted with the curing agent. 6, drying time: dry at room temperature, surface drying time of 5-10 minutes, doing time in less than 24 hours, 80 deg c bake for 20 minutes can dry quickly. 7, after you have added curing agents use time: 4-6 hours, expired please discard used, surplus ink can not be recovered. "Testing" 1, 3M tape hundred tests: no loss 2, punch resistance test: 1mm thick aluminum plate 180 ° bending was not changed. 3, resistance to alcohol testing: concentration 99% industrial alcohol with cotton wool dipped in 500G strength 200 times without bleaching. "Note" 1, a small print to confirm trial meets the requirements prior to mass production. 2, remove grease and impurities on the surface of the substrate, in order to promote adhesion effect. 3, adhesion, hardness, resistance to acid, alcohol, chemical resistance, scratch resistance, wear resistance, such as performance testing, needs to fully cure before making an inspection. 4, cases without permission, this series ink may not be mixed with other types of ink and color matching. 5, ink, thinner, use and storage of fireworks is prohibited. 6 be aware of construction, the use of the ventilation of the premises in good condition, try to avoid direct skin contact. Entrance 7, this product is accidentally spilled, nose, eye, ear, using large amounts of water to wash or to seek help directly from the doctor/