PP油墨 承 印 物：PP（聚丙烯）、PE（聚乙烯）及類似材料 終產品舉例：各類文具、各類包裝瓶罐（洗發水、化妝品包裝）、蓄電池等產品特性。 產品特性：印刷品表面平滑，光澤好于PPF系列，對PP、PE材料有良好的附著力，印刷適應性佳，高耐磨性。 使用方法：1、網目：150-350網目。 2、網版：耐有機溶劑感光膠制作網版。 3、刮刀：60-90℃,耐溶劑刮刀,如聚胺脂刮刀。 4、用量：每公斤用250目網版可印刷36平方米。 5、印刷（印前準備,印刷過程）。 干　燥：自然揮發干燥（表干20分鐘、實干24小時以上）或100℃以下熱風吹干 選用溶劑：719快干水，718中干水，783慢干水，因印刷環境溫度、通風量及印刷圖案大小不同進行適當選擇網板清洗：選用溶劑清洗（如：洗網水） 產品包裝：1公斤裝、5公斤裝、20公斤裝儲存條件：5℃—25℃條件下可存放兩年，避免強光照射、防接觸強酸、強堿，用塑膠罐包裝。 注意事項： １、使用該產品進行印刷時，因PP、PE材質的表面張力較大，請先作好測試后再進行印刷。對于PE材料，有可能產生附著力不佳的現象，這時可以加入2%—5%的PP附著力促進劑進行印刷測試，視其效果。 ２、對于表面張力較小的材料，可先用PP處理水或火焰處理法對底材進行處理后印刷，這樣可以提高油墨的附著力。 ３、該油墨屬于慢反應固著型油墨，測試附著力必需在印刷后24小時以上再進行測試。 PP ink printing: PP (polypropylene), PE (polyethylene) and similar materials, final product, for example: various types of stationery, various types of bottles (shampoo, cosmetics packaging), batteries and other product features. Product features: print surface smoothness and gloss to the PPF series, good adhesion on PP, PE material, good printability, high resistance to wear. Method of use: 1, mesh: mesh 150-350. 2, Online Edition: organic solvent emulsion production network Edition. 3, blade: 60-90, solvent-resistant scraper, such as polyurethane scraper. 4, use: printing per kg 250 mesh version 36 square meters. 5, printing (pre-press preparation, printing process). Dry: natural volatile dry (table dry 20 minutes, and work 24 hours above) or 100 ℃ following hot air blow dry selection solvent: 719 fast dry water, 718 in the dry water, 783 slow dry water, due to printing environment temperature, and ventilation volume and the printing pattern size different for appropriate Select Network Board cleaning: selection solvent cleaning (as: wash network water) products packaging: 1 kg loaded, and 5 kg loaded, and 20 kg loaded store conditions: 5 ℃-25 ℃ conditions Xia can store two years, avoid strong light irradiation, and anti-contact acid, and alkali, Packing in plastic tanks. Note: when printing 1, the use of the product, due to greater surface tension of PP, PE material, please make test before you print. For PE material, possibly resulting in poor adhesion of the phenomena, and can then join 2%-5% PP adhesion promoter for printing test, depending on the effect. 2, for less tension in the surface material, or flame them in PP processing method for processing substrate printing, thus improving ink adhesion. 3 solid inks, the ink is slow reaction and adhesion must be in print for more than 24 hours after the test to test.